Model NO.: GB500C
Conditions of Use: Land Use
Usage: Common Units
Landuse Type of Unit: Low Noise
Excitation Mode: AC Rotating Exciter
Trademark: As Required
Transport Package: Carton Inside, Iron Bracket Outside
Specification: 3300x1400x1950mm
Origin: China
HS Code: 85021100
Model NO.: GB500C
Conditions of Use: Land Use
Usage: Common Units
Landuse Type of Unit: Low Noise
Excitation Mode: AC Rotating Exciter
Trademark: As Required
Transport Package: Carton Inside, Iron Bracket Outside
Specification: 3300x1400x1950mm
Origin: China
HS Code: 85021100
| Cummins 500KW Prime diesel generator(50HZ) |
| Model of Genset |
GB500C |
| Specifications of Generator set |
Frequency |
50HZ |
| Voltage |
  400/230V |
| Prime output(KW) |
500KW |
| Standby output(KW) |
550KW |
| Power factor |
0.8 lagging |
| Phase |
3-phase |
| Engine Brand |
CUMMINS |
| Engine model |
KTAA19-G6A |
| Type |
Vertical, In-line,4Cycle,turbocharged and intercooled |
| Number of Cylinders |
6 |
| Bore x Stroke |
159 x 159 |
| Displacement (L) |
19 |
| Engine Speed(rpm/min) |
1500 |
| Engine prime power(KW) |
549 |
| Engine standby power(KW) |
610 |
| Starting/Battery Charging System |
Starter batteries:maintenance free type, with rack cables, 45A charging alternator, fuel shut off solenoid, 24V starting motor |
| Fuel Tank Capacity (L) |
1000L base tank |
| Fuel consumption(L) |
at full load |
156 |
| At ¾ Load |
116 |
| At ½ Load |
80 |
| Water Pre-heater Jacket |
included |
| Alternator model(KH-Stamford, China Brand) |
HCIÂ 544FS |
| Insulation |
Class H |
| Voltage Regulator |
Automatic |
| Control panel |
Smartgen 6110 digital controller, 1000A air breaker,  transfer switch, temp.and pressure gauges, indicating lamp, hour meter, etc. |
| Emergency Stop System |
Low oil pressure, high water temperature, Over-speed and over load |
| DIMENSIONSÂ ANDÂ WEIGHTS |
 |
| Open type |
Dimension(LxWxH)(mm) |
4200x1750x2220 |
| Weight(kg) |
4950 |
| Silent type |
Dimension(LxWxH)(mm) |
5400x1800x2350
|
| Weight(kg) |
5580 |
Â
| Cummins 500KW Prime diesel generator(50HZ) |
| Model of Genset |
GB500C |
| Specifications of Generator set |
Frequency |
50HZ |
| Voltage |
  400/230V |
| Prime output(KW) |
500KW |
| Standby output(KW) |
550KW |
| Power factor |
0.8 lagging |
| Phase |
3-phase |
| Engine Brand |
CUMMINS |
| Engine model |
KTAA19-G6A |
| Type |
Vertical, In-line,4Cycle,turbocharged and intercooled |
| Number of Cylinders |
6 |
| Bore x Stroke |
159 x 159 |
| Displacement (L) |
19 |
| Engine Speed(rpm/min) |
1500 |
| Engine prime power(KW) |
549 |
| Engine standby power(KW) |
610 |
| Starting/Battery Charging System |
Starter batteries:maintenance free type, with rack cables, 45A charging alternator, fuel shut off solenoid, 24V starting motor |
| Fuel Tank Capacity (L) |
1000L base tank |
| Fuel consumption(L) |
at full load |
156 |
| At ¾ Load |
116 |
| At ½ Load |
80 |
| Water Pre-heater Jacket |
included |
| Alternator model(KH-Stamford, China Brand) |
HCIÂ 544FS |
| Insulation |
Class H |
| Voltage Regulator |
Automatic |
| Control panel |
Smartgen 6110 digital controller, 1000A air breaker,  transfer switch, temp.and pressure gauges, indicating lamp, hour meter, etc. |
| Emergency Stop System |
Low oil pressure, high water temperature, Over-speed and over load |
| DIMENSIONSÂ ANDÂ WEIGHTS |
 |
| Open type |
Dimension(LxWxH)(mm) |
4200x1750x2220 |
| Weight(kg) |
4950 |
| Silent type |
Dimension(LxWxH)(mm) |
5400x1800x2350
|
| Weight(kg) |
5580 |
Â
Horizontal Machining Centers
Horizontal machining center refers to a machining center where the spindle is parallel to the worktable, usually equipped with an automatic indexing rotary worktable, which generally has 3-5 motion coordinates. The worktable of a horizontal machining center is designed to move only in the X or Y direction, and the worktable form is generally a rotating worktable with a lattice screw hole table, which is relatively easy to install an exchange type dual worktable. The common method is to add three linear motion coordinates and one rotary motion coordinate. After a single clamping, the workpiece completes the machining of the other four surfaces except for the installation surface and top surface. It is most suitable for adding box type parts.
Horizontal Machining Centers characteristics:
1.Horizontal machining center structural characteristics: A horizontal machining center refers to a complex structure with the spindle parallel to the workbench, occupying a large area, and being relatively expensive. Due to the fact that the spindle is parallel to the worktable, the rotation axis of the spindle is parallel to the worktable, which allows for a wider range of machining operations. Horizontal machining centers are usually suitable for processing large workpieces and parts that require multi sided machining.
2. Horizontal machining center application characteristics: Due to its complex structure, large footprint, and high price, horizontal machining centers are usually suitable for processing large parts and multi sided machining parts. Due to the parallel spindle of the horizontal machining center to the worktable, it can achieve simultaneous machining of multiple surfaces and improve production efficiency. Horizontal machining centers are also suitable for large parts that require rough and precision machining, such as machine tool beds, automotive components, etc.
3. Horizontal machining center processing characteristics: Due to its complex structure, large footprint, and high cost, horizontal machining centers are usually suitable for processing large parts and multi sided machining parts. Due to the parallel spindle of the horizontal machining center to the worktable, it can achieve simultaneous machining of multiple surfaces and improve production efficiency. Horizontal machining centers are also suitable for large parts that require rough and precision machining, such as machine tool beds, automotive components, etc.
Horizontal Machining Center,HMC Machining Center,Horizontal Machining Centre,Machining Center, Machining Centre
Dongguan Liyang Intelligent Technology Co., Ltd , https://www.leyomachine.com